Showing posts with label Networking. Show all posts
Showing posts with label Networking. Show all posts

Networking |MCQ Networking |Competitive Examination | Set15

1 comment

Q.1. In a synchronous modem, the receive equalizer is known as
a. adaptive equalizer
b. impairment equalizer
c. statistical equalizer
d. compromise equalizer
Answer:a
Q.2. RS-449/442-A/423-A is
a. a check bit appended to an array of binary digits to make the sum of the all the binary digits
b. a set of physical layer standards developed by EIA and intended to replace RS-232-C
c. a code in which each expression conforms to specific rules of construction, so that if certain errors occur in an expression the resulting expression will not conform to the rules of construction and thus the presence of the errors is detected
d. the ratio of the number of data units in error to the total number of data units
Answer: b
Q.3. Alex is required to provide information on how many people are using the network at any one time. Which network will enable him to do so ?
a. Ethernet
b. Token-Ring
c. Server-based
d. Star
Answer: c
Q.4. Which of the following digits are known as the area code of the Network User Address (NUA) ? 
a. The CCITT Recommendation X.25 specifies three layers of communication: physical, link and network
b. The second layer of communication is the data-link layer
c. Errors in the physical layer can be detected by the data link layer
d. The fourth layer, in reference to the OSI model, is the session layer
Answer: d
Q.5.Devices on one network can communicate with devices on another network via a
a. 5-7
b. 1-4
c. 8-12
d. 13-14
Answer: a
Q.6. Now-a-days computers all over the world can talk to each other. Which is one of the special accessories essential for this purpose
a. Keyboard .
b. Scanner .
c. Modem
d. All of the above.
Answer: c
Q.7. End-to-end connectivity is provided from host-to-host in ?
a. Network layer
b. Session layer
c. Data link layer
d. Transport layer
Answer: d
Q.8. To make possible the efficient on-line servicing of many teleprocessing system users on large computer systems, designers are developing ?
a. communication systems
b. multiprogramming systems
c. virtual storage systems
d. All of the above
Answer: d
Q.9. A form of modulation In which the amplitude of a carrier wave is varied in accordance with some characteristic of the modulating signal, is known as ?
a. Amplitude modulation
b. modem
c. Aloha
d. None of the above
Answer: a
Q.10. Which of the following best describes the scopes on each DHCP server, in the absence of configuration problems with DHCP addresses, if you use multiple DHCP servers in your environment ?
a. Unique to that subnet only
b. For different subnets
c. For no more than two subnets
d. For no subnets
Answer: b
Q.11. CSMA (Carrier Sense Multiple Access) is ?
a. a method of determining which device has access to the transmission medium at any time
b. a method access control technique for multiple-access transmission media
c. a very common bit-oriented data link protocol issued by ISO
d. network access standard for connecting stations to a circuit-switched network
Answer: b
Q.12. Which of the following summation operation is performed on the bits to check an error-detecting code ?
a. Codec
b. Coder-decoder
c. Checksum
d. Attenuation
Answer: c
Q.13. The main difference between TCP and UDP is :
a. UDP is connection oriented where as TCP is datagram service
b. TCP is an Internet protocol where as UDP is an ATM protocol
c. UDP is a datagram where as TCP is a connection oriented service
d. All of the above
Answer: c
Q.14. The standard suit of protocols used by the Internet, intranets, extranets, and some other networks ?
a. TCP/IP
b. Protocol
c. Open Systems
d. Internetwork processor
Answer: a
Q.15. What operates in the Data Link and the Network layer ?
a. NIC
b. Bridge
c. Brouter
d. Router
Answer: c
Q.16. Networks that follow the 802.5 standard appear to be in a star topology but are actually operating in what type of topology ?
a. Linear bus
b. Modified star
c. Modified ring
d. Ring
Answer: d
Q.17. What is the name of the computer based EMMS that provides a common forum where users can check in at their convenience, post messages, actively exchange ideas and participate in ongoing discussions ?
a. E-mail
b. Bulletin board system (BBS)
c. Teleconferencing
d. Videoconferencing
Answer: b
Q.18. A communications device that combines transmissions from several 1/ O devices into one line is a:
a. concentrator
b. modifier
c. multiplexer
d. full-duplex line
Answer: c
Q.19. Which of the following statement is incorrect ?
a. The CCITT Recommendation X.25 specifies three layers of communication: physical, link and network.
b. The second layer of communication is the data-link layer
c. Errors in the physical layer can be detected by the data link layer
d. The fourth layer, in reference to the OSI model, is the session layer
Answer: d
Q.20. Devices on one network can communicate with devices on another network via a ?
a. file server
b. utility server
c. printer server
d. gateway
Answer:d


Previous Next



:: Click the links below for similar type Questions and answers ::



Read more »

Posted in: ,,

Networking | MCQ Networking | Set 14

No comments

Q.1.The main difference between TCP and UDP is
a.UDP is connection oriented where as TCP is datagram service
b.TCP is an Internet protocol where as UDP is an ATM protocol
c.UDP is a datagram where as TCP is a connection oriented service
d.All of the above
Answer:c
Q.2.What operates in the Data Link and the Network layer?
a. NIC
b. Bridge
c. Brouter
d. Router
Answer: c
Q.3. What is the name of the computer based EMMS that provides a common forum where users can check in at their convenience, post messages, actively exchange ideas and participate in ongoing discussions?
a. E-mail
b. Bulletin board system (BBS)
c. Teleconferencing
d. Videoconferencing
Answer: b
Q.4.Which of the following statement is incorrect? 
a. The CCITT Recommendation X.25 specifies three layers of communication: physical, link and network
b. The second layer of communication is the data-link layer
c. Errors in the physical layer can be detected by the data link layer
d. The fourth layer, in reference to the OSI model, is the session layer
Answer: d
Q.5.Devices on one network can communicate with devices on another network via a
a. file server
b. utility server
c. printer server
d. gateway
Answer: d
Q.6. A hard copy would be prepared on a
a. typewriter terminal.
b. line printer.
c. plotter
d. All of the above.
Answer: d
Q.7. Which of the following device copies electrical signals from one Ethernet to another?
a. bridge
b. repeater
c. hub
d. passive hub
Answer: b
Q.8. Stephanie is in charge of a small network and wants to make it simple but secure. The users want to have full control over their data and still be able to share data with the rest of the office. The networking knowledge of the office staff is basic. Which network(s) would be the best for Stephanie to set up?
a. Peer-to-peer
b. Master domain
c. Server-based
d.WAN
Answer: c
Q.9.When UPC is used, the price of the item is located ?
a. on the item
b. on the item and on the shelf
c. in computer storage
d. on the shelf and in computer storage
Answer: d
Q.10. Error control is needed at the transport layer because of potential errors occurring _____.
a. from transmission line noise
b. in routers
c. from out-of-sequence delivery
d. from packet losses
Answer: b
Q.11. Which of the following is not a standard synchronous communication protocol?
a. SDLC
b. SMTP
c. SLIP
d. PAS
Answer: d
Q.12. The network layer, in reference to the OSI model, provide
a. data link procedures that provide for the exchange of data via frames that can be sent and received
b. the interface between the X.25 network and packet mode device
c. the virtual circuit interface to packet-switched service
d. All of the above
Answer: c
Q.13. In OSI network architecture, the routing is performed by:
a. network layer
b. data link layer
c. transport layer
d. session layer
Answer: a
Q.14. Which of the following communications lines is best suited to interactive processing applications?
a. narrowband channels
b. simplex lines
c. full-duplex lines
d. mixed band channels
Answer: c
Q.15. What is the first octet range for a class B IP address?
a. 128 - 255
b. 1 - 127
c. 192 - 223
d. 128 - 191
Answer: d
Q.16. If communication software can be called the "traffic cop" of a micro communication system, then what should the modem be called?
a. Park
b. Bridge
c. Interface
d. Link
Answer: b
Q.17. Which of the following specifies the network address and host address of the computer?
a. The IP address
b. The TCP address
c. The subnet mask
d. controller
Answer: a
Q.18. For connecting modem, a computer must be equipped with a port that conforms to the RS-232 standard of the Electronic Industries Association of America. What do the letters 'RS' stand for?
a. Recognised standard
b. Random sequence
c. Recommended standard
d. Registered source
Answer: c
Q.19. A network that requires human intervention of route signals is called a
a. bus network
b. ring network
c. star network
d. T-switched network
Answer: d
Q.20.What is the port number for POP3?
a. 110
b. 90
c. 80
d. 49
Answer: a

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set 13

No comments

Q.1.What protocol is used between E-Mail servers?
a.FTP
b.SMTP
c.SNMP
d.POP3
Answer:b
Q.2. If you configure the TCP/IP address and other TCP/IP parameters manually, you can always verify the configuration through which of the following? Select the best answer?
a. Network Properties dialog box
b. Server Services dialog box
c. DHCPINFO command-line utility
d. Advanced Properties tab of TCP/ IP Info
Answer: a
Q.3. In a PC to telephone hookup for long distance communication, modem is connected between the telephone line and
a. PC
b. synchronous port
c. crossover cable
d. asynchronous port
Answer: d
Q.4. Which of the following communications service provides message preparation and transmission facilities? 
a. Teletex
b. Teletext
c. x400
d. Fax
Answer: a
Q.5. Four bits are used for packet sequence numbering in a sliding window protocol used in a computer network. What is the maximum window size?
a. 4
b. 8
c. 15
d. 16
Answer: c
Q.6. In a synchronous modem, the receive equalizer is known as
a. adaptive equalizer.
b. impairment equalizer.
c. statistical equalizer.
d. compromise equalizer.
Answer: a
Q.7. Alex is required to provide information on how many people are using the network at any one time. Which network will enable him to do so?
a. Server-based
b. Token-Ring
c. Ethernet
d. Star
Answer: a
Q.8. Now-a-days computers all over the world can talk to each other. Which is one of the special accessories essential for this purpose?
a. Keyboard
b. Modem
c. Scanner
d.Fax
Answer: b
Q.9. To make possible the efficient on-line servicing of many teleprocessing system users on large computer systems, designers are developing?
a. communication systems
b. multiprogramming systems
c. virtual storage systems
d. All of the above
Answer: d
Q.10. Which of the following best describes the scopes on each DHCP server, in the absence of configuration problems with DHCP addresses, if you use multiple DHCP servers in your environment?
a. Unique to that subnet only
b. For different subnets
c. For no more than two subnets
d. For no subnets
Answer: b
Q.11. Which of the following provides a storage mechanism for incoming mail but does not allow a user to download messages selectively?
a. SMTP
b. DHCP
c. IMAP
d. POP3
Answer: d
Q.12. A 4 KHz noiseless channel with one sample every 125 per sec, is used to transmit digital signals. Find the bit rate (bits per second) that are sent, if CCITT 2.048 Mbps encoding is used.?
a. 500 Kbps
b. 32 Kbps
c. 8 Kbps
d. 64 Kbps.
Answer: d
Q.13. A subdivition of main storage created by operational software is referred to as a:
a. compartment
b. time-shared program
c. divided core
d. partition
Answer: d
Q.14. On a class C network with a subnet mask of 192, how many subnets are available?
a. 254
b. 62
c. 2
d. 14
Answer: c
Q.15. How can you see the address of the DHCP server from which a client received its IP address?
a. By using Advanced Properties of TCP/IP
b. By using IPCONFIG/ALL
c. By using DHCPINFO
d. By pinging DHCP
Answer: b
Q.16. RS-232-G
a. is an interface between two data circuit terminating equipment as examplified by a local and remote modem
b. is an interface standard between Data terminal Equipment and Data Circuit Terminating Equipment
c. specifies only the mechanical characteristics of an interface by providing a 25-pin connector
d. requires only 7 pin out of 25 in order to transmit digital data over public telephone lines
Answer: b
Q.17. Error detection at a data link level is achieved by?
a. bit stuffing
b. cyclic redundancy codes
c. Hamming codes
d. equalization
Answer: b
Q.18. Which of the following items is not used in Local Area Networks (LANs)?
a. Computer
b. Modem
c. Printer
d. Cable
Answer: b
Q.19. The 32-bit internet address 10000000 00001010 00000010 00011110 will be written in dotted decimal notation as
a. 148.20.2.30
b. 164.100.9.61
c. 128.10.2.30
d. 210.20.2.64
Answer: d
Q.20.You have a class A network address 10.0.0.0 with 40 subnets, but are required to add 60 new subnets very soon. You would like to still allow for the largest possible number of host IDs per subnet. Which subnet mask should you assign?
a. 255.240.0.0
b. 255.248.0.0
c. 255.252.0.0
d. 255.254.0.0
Answer: d

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set-12

No comments

Q.1. Which of the following is a voiceband channel?
a.Telephone line
b.Telegraph line
c.Coaxial cable
d.Microwave systems
Answer: a
Q.2. How much power (roughly) a light emitting diode can couple into an optical fiber?
a. 100 microwatts
b. 440 microwatts
c. 100 picowatts
d. 10 miliwatts
Answer: a
Q.3. The synchronous modems are more costly than the asynchronous modems because
a. they produce large volume of data
b. they contain clock recovery circuits
c. they transmit the data with stop and start bits
d. they operate with a larger bandwidth
Answer: b
Q.4. Which of the following statement is correct? 
a. terminal section of a synchronous modem contains the scrambler
b. receiver section of a synchronous modem contains the scrambler
c. transmission section of a synchronous modem contains the scrambler
d. control section of a synchronous modem contains the scrambler
Answer: c
Q.5. In a synchronous modem, the digital-to-analog converter transmits signal to the
a. equilizer
b. modulator
c. demodulator
d. terminal
Answer: a
Q.6. Which of the following communications lines is best suited to interactive processing applications?
a. narrow band channel.
b. simplex lines.
c. full duplex lines.
d. mixed band channels.
Answer: c
Q.7. Contention is
a. One or more conductors that serve as a common connection for a related group of devices
b. a continuous frequency capable of being modulated or impressed with a second signal
c. the condition when two or more stations attempt to use the same channel at the same time
d. a collection of interconnected functional units that provides a data communications service among stations attached to the network
Answer: c
Q.8. Avalanche photodiode receivers can detect hits of transmitted data by receiving
a. 100 photons
b. 300 photons
c. 400 photons
d. 200 photons
Answer: d
Q.9. Satellite-Switched Time-Division Multiple Access (SS/TDMA) is
a. the method of determining which device has access to the transmission medium at any time
b. a medium access control technique for multiple access transmission media
c. a form of TDMA in which circuit switching is used to dynamically change the channel assignments
d. All of the above
Answer: c
Q.10.When you ping the loopback address, a packet is sent where:
a. On the network
b. Down through the layers of the IP architecture and then up the layers again
c.Across the wire
d. through the loopback dongle
Answer: b

Previous Next

:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set-11

No comments

Q.1. Error detection at a data link level is achieved by
a.bit stuffing
b.cyclic redundancy codes
c.Hamming codes
d.equalization
Answer: b
Q.2. When the computer provides the manager with a multiple choice of possible answers, the prompting technique is
a. question and answer
b. form filling
c. open-ended question
d. menu selection
Answer: d
Q.3. Which data communication method is used to transmit the data over a serial communication link?
a. simplex
b. half-duplex
c. full-duplex
d. None of above
Answer: c
Q.4. What is the minimum number of wires needed to send data over a serial communication link layer? 
a. 1
b. 2
c. 4
d. 6
Answer: b
Q.5. Most data communications involving telegraph lines use:
a. simplex lines
b. wideband channel
c. narrowband channel
d. dialed service
Answer: c
Q.6. A communications device that combines transmissions from several I/O devices into one line is a
a. concentrator.
b. modifier.
c. multiplexer.
d. full-duplex line.
Answer: c
Q.7. Sending a file from your personal computer's primary memory or disk to another computer is called
a. uploading
b. downloading
c. logging on
d. hang on
Answer: a
Q.8. What is the name of the software package that allows people to send electronic mail along a network of computers and workstations?
a. Memory resident package
b. Project management package
c. Data communication package
d. Electronic mail package
Answer: c
Q.9. The communication mode that supports two-way traffic but only one direction at a time is
a. simplex
b. duplex
c. half duplex
d. multiplex
Answer: c
Q.HMP (Host Monitoring Protocol) is:
a. a TCP/IP protocol used to dynamically bind a high level IP Address to a low-level physical hardware address
b. a TCP/IP high level protocol for transferring files from one machine to another
c. a protocol used to monitor computers
d. a protocol that handles error and control messages
Answer: c

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set-10

No comments

Q.1. Which of the following is an advantage to using fiber optics data transmission?
a.resistance to data theft
b.fast data transmission rate
c.low noise level
d.all of above
Answer: d
Q.2. Which of the following is required to communicate between two computers?
a. communications software
b. protocol
c. communication hardware
d. all of above including access to transmission medium
Answer: d
Q.3. The transmission signal coding method of TI carrier is called
a. Bipolar
b. NRZ
c. Manchester
d. Binary
Answer: a
Q.4. .  How many bits internet address is assigned to each host on a TCP/IP internet which is used in all communications with the host? 
a. Contention
b. Synchronous
c. Asynchronous
d. Collision
Answer: d
Q.5. The interactive transmission of data within a time sharing system may be best suited to
a. 16 - bits
b. 32 - bits
c. 48 - bits
d. 64 - bits
Answer: b
Q.6. With an IP address of 100, you currently have 80 subnets. What subnet mask should you use to maximize the number of available hosts?
a. 192.
b. 252.
c. 240.
d. 248.
Answer: b
Q.7. Which of the following types of channels moves data relatively slowly?
a. wideband channel
b. voiceband channel
c. broadband channel
d. narrowband channel
Answer: d
Q.8. Which of the following is required to communicate between two computers?
a. communications software
b. protocol
c. communications hardware
d. All of the above
Answer: d
Q.9. A machine that connects to two or more electronic mail systems and transfers mail messages among them is known as
a. Gateways
b. mail gateway
c. bridges
d. User Agent
Answer: b
Q.. If digital data rate of 9600 bps is encoded using 8-level phase shift keying (PSK) method, the modulation rate is
a. 1200 bands
b. 3200 bands
c. 4800 bands
d. 9600 bands
Answer: b

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set-09

No comments

Q.1. What are the most commonly used transmission speeds in BPS used in data communication?
a.300
b.1200
c.2400
d.9600
Answer: d
Q.2. What is the default subnet mask for a class C network?
a. 127.0.0.1
b. 255.0.0.0
c. 255.255.0.0
d. 255.255.255.0
Answer: d
Q.3. Which of the following is used for modulation and demodulation?
a. modem
b. protocols
c. gateway
d. multiplexer
Answer: a
Q.4. Which of the following is not a disadvantage of wireless LAN? 
a. Slower data transmission
b. higher error rate
c. interference of transmissions from different computers
d. All of the above
Answer: d
Q.5. Which of the following refers to the terms "residual error rate"?
a. the number of bit errors per twenty four hours of continuous operation on an asynchronous line
b. The probability that one or more errors will be undetected when an error detection scheme is used
c. the probability that one or more errors will be detected when an error detection mechanism is used
d. signal to noise ratio divided by the ratio of energy per bit to noise per hertz
Answer: b
Q.6. Which of the following summation operations is performed on the bits to check an error-detecting code?
a. Codec.
b. Coder-decoder
c. Checksum.
d. Attenuation
Answer: d
Q.7. Which of the following is considered a broad band communication channel?
a. coaxial cable
b. fiber optics cable
c. microwave circuits
d. All of the above
Answer: c
Q.8. An error-detecting code inserted as a field in a block of data to be transmitted is known as?
a. Frame check sequence
b. Error detecting code
c. Checksum
d. flow control
Answer: a
Q.9. The cheapest modems can transmit
a. 1,200 bits per second
b. 300 bits per second
c. 2,400 bits per second
d. 4,800 bits per second
Answer: b
Q.. Which network topology is considered passive?
a. Cross
b. Bus
c. Star
d. Ring
Answer: b

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set 08

No comments

Q.1. What device separates a single network into two segments but lets the two segments appear as one to higher protocols?
a.Switch
b.Gateway
c.Bridge
d.Router
Answer: c
Q.2. What is the number of separate protocol layers at the serial interface gateway specified by the X.25 standard?
a. 4
b. 2
c. 3
d. 6
Answer: c
Q.3. Frames from one LAN can be transmitted to another LAN via the device
a. Router
b. Bridge
c. Repeater
d. Modem
Answer: b
Q.4. Which of the following condition is used to transmit two packets over a medium at the same time? 
a. Contention
b. Synchronous
c. Asynchronous
d. Collision
Answer: d
Q.5. The interactive transmission of data within a time sharing system may be best suited to
a. simplex lines
b. half-duplex lines
c. full duplex lines
d. biflex-lines
Answer: b
Q.6. Which of the following statement is incorrect?
a. The difference between synchronous and asynchronous transmission is the clocking derived from the data in synchronous transmission.
b. Half duplex line is a communication line in which data can move in two directions, but not at the same time.
c. Teleprocessing combines telecommunications and DP techniques in online activities.
d. Batch processing is the prefered processing mode for telecommunication operation.
Answer: d
Q.7. Which of the following is considered a broad band communication channel?
a. coaxial cable
b. fiber optics cable
c. microwave circuits
d. All of the above
Answer: d
Q.8. Which of the following is not a transmission medium?
a. telephone lines
b. coaxial cables
c. modem
d. microwave systems
Answer: c
Q.9. Which of the following does not allow multiple uses or devices to share one communication line?
a. doubleplexer
b. multiplexer
c. concentrator
d. controller
Answer: a
Q.You have a class A network address 10.0.0.0 with 40 subnets, but are required to add 60 new subnets very soon. You would like to still allow for the largest possible number of host IDs per subnet. Which subnet mask should you assign?
a. 255.240.0.0
b. 255.248.0.0
c. 255.252.0.0
d. 255.254.0.0
Answer: d

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set 07

No comments

Q.1. Each web page has its own unique address known as
a.Uniform Resource Locator
b.Universal Resource Location
c. Uniform Resource Location
d. Universal Resource Locator
Answer: b
Q.2. A station in a network forwards incoming packets by placing them on its shortest output queue. What routing algorithm is being used?
a. hot potato routing
b. static routing
c. delta routing
d. None of the above
Answer: a
Q.3. . Layer one of the OSI model is
a. physical layer
b. link layer
c. transport layer
d. network layer
Answer: a
Q.4. The x.25 standard specifies a 
a. technique for start-stop data
b. technique for dial access
c. data bit rate
d. DTE/DCE interface
Answer: d
Q.5. Which of the following communication modes support two-way traffic but in only one direction at a time?
a. simplex
b. half duplex
c. three-quarters duplex
d. all of the above
Answer: b
Q.6. Which of the following might be used by a company to satisfy its growing communications needs?
a. front end processor
b. multiplexer
c. controller
d. All of the above
Answer: d
Q.7. The geostationary satellite used for communication systems
a. rotates with the earth
b. remains stationary relative to the earth
c. is positioned over equator
d. All of the above
Answer: d
Q.8. Telecommunication networks frequently interconnect an organization with its customers and suppliers. Select the best fit for answer
a. Bandwidth alternatives
b. Switching alternating
c. Extranets
d. Inter organizational networks
Answer: d
Q.9. The packets switching concept was first proposed
a. in the late 1980s for the Defense Ministry of US
b. in the early 1960s for military communication systems, mainly to handle speech
c. in the late 1950s for Defense Ministry of US
d. All of the above
Answer: b
Q.10. The _____ houses the switches in token ring
a. transceiver
b. nine-pin connector
c. MAU
d. NIC
Answer: c

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set 06

No comments

Q.1.Which of the following is not basic network topology?
a. Bus.
b. Ring
c. Star
d. Mesh
Answer: d
Q.2. . Which is the network model where a host computer is connected to other computers to provide data or computing services via network?
a. Centralized Network
b. Client / Server Network
c. Peer-to-peer Network
d. None of above
Answer: a
Q.3. . A software program that controls other software and hardware that runs on a network
a. NIC
b. NOS
c. POP
d. TCP/IP
Answer: b
Q.4. In OSI network architecture, the dialogue control and token management are responsibility of
a. Session layer
b. Network layer
c. Transport layer
d. Data link layer
Answer: a
Q.5. In OSI network architecture, the routing is performed by
a. network layer
b. data link layer
c. transport layer
d. session layer
Answer: a
Q.6. Which of the following performs modulation and demodulation?
a. fiber optics
b. satellite
c. coaxial cable
d. modem
Answer: d
Q.7. Tim Berners Lee is credited for the creation of
a. Web email system
b. world wide web
c. File Transfer Protocol
d. All of above
Answer: b
Q.8. The process of converting analog signals into digital signals so they can be processed by a receiving computer is referred to as:
a. Modulation
b. Demodulation
c. Synchronizing
d. Digitizing
Answer: d
Q.9. How many OSI layers are covered in the X.25 standard?
a. Two
b. Three
c. Seven
d. Six
Answer: b
Q.10. How many digits of the DNIC (Data Network Identification Code) identify the country?
a. first three
b. first four
c. first five
d. first six
Answer: a

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set 05

No comments

Q.1. Which server computer that is configured to serve file transfer and storage, data migration, file updates synchronization?
a. FTP Server.
b. Database Server
c. File Server
d. None of above
Answer: c
Q.2. . Which of the following is responsible for approving standards and allocating resources in the Internet?
a. Internet Architecture Board (IAB)
b. Internet Engineering Task Force (IETF)
c. InterNIC
d. None of above
Answer: a
Q.3. . Which body in Internet provides the registration services to Internet community?
a. Internet Architecture Board (IAB)
b. Internet Engineering Task Force (IETF)
c. InterNIC
d. None of above
Answer: c
Q.4. Which of the following is considered a broad band communication channel?
a. coaxial cable
b. fiber optics cable
c. microwave circuits
d. all of above
Answer: d
Q.5. Which of the following is not email service?
a. Hotmail
b. Gmail
c. Yahoo
d. None of above
Answer: c
Q.6. Which of the following application is required to read your email in Hotmail?
a. A computer with browser and internet connection
b. Outlook Express or Microsoft Outlook
c. Eudora Pro
d. All of above
Answer: a
Q.7. Tim Berners Lee is credited for the creation of
a. Web email system
b. world wide web
c. File Transfer Protocol
d. All of above
Answer: b
Q.8. Which of the following is not a transmission medium?
a. Telephone lines
b. Coaxial cables
c. Modem
d. Microwave systems
Answer: c
Q.9. A network computer that utilizes the resources of other network computers is known as a
a. Server
b. Host computer
c. Client
d. Media
Answer: d
Q.10. A group of computers connected together to communicate and share resources is known as
a. A computer network
b. A server
c. A client
d. Authentication
Answer: a

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

Networking | MCQ Networking | Set 04

No comments

Q.1. What is the powerful, centralized computer system that performs data storage and processing tasks on behalf of clients and other network devices ?
a. Client.
b.Host computer
c.Terminal
d.Network
Answer: b
Q.2. A self-sufficient computer that acts as both a server and a client is known as
a. Host
b. Client
c. Server
d. Peer
Answer: d
Q.3. . A server computer that is configured to serve file transfer and storage, data migration, file updates synchronization is
a. FTP Server
b. Database Server
c. File Server
d. None of above
Answer: c
Q.4. Which of the following is responsible for approving standards and allocating resources in the Internet?
a. Internet Architecture Board (IAB)
b. Internet Engineering Task Force (IETF)
c. InterNIC
d. None of above
Answer: a
Q.5. Which body in Internet provides the registration services to Internet community?
a. Internet Architecture Board (IAB)
b. Internet Engineering Task Force (IETF)
c. InterNIC
d. None of above
Answer: c
Q.6.Who is responsible for discussing and investigating the operational and technical problems of Internet?
a. Internet Architecture Board (IAB)
b. Internet Engineering Task Force (IETF)
c. InterNIC
d. None of above
Answer: b
Q.7. Which is the channel handle moderate data volumes in transmission rate between 110 to 9600 bps?
a. Narrowband channel
b. Voice band channel
c. Broadband channel
d. None of abover
Answer: b
Q.8. A high speed, high capacity transmission medium that can carry signals from multiple independent network carrier is?
a. Narrowband channel
b. Voice band channel
c. Broadband channel
d. None of above
Answer: c
Q.9. The internet was developed by US
a. Department of Defense
b. Department of Electronics
c. Department of Commerce
d. None of above
Answer: a
Q.10. A user can get files from another computer by using
a. File Transfer Protocol
b. TCP/IP
c. Internet Protocol
d. None of above
Answer: a

Previous Next


:: Click the links below for similar type Questions and answers ::

Read more »

Posted in: ,,,

 
Design by Wordpress Theme | Bloggerized by Free Blogger Templates | coupon codes